1 Inch NO Lead Brass Water Valve System Responds to Water Sensor by Closing Valve
Keep water lead levels low. This MADE IN USA no lead brass ball valve in the WaterCop Sergeant basic automatic water protection package meets the low lead standards for California and Vermont water valves. Get both water damage protection and the knowledge your exposure to lead in water is minimal. Use for whole house protection with installation on your main water pipe or zone a larger home or business with several units. Low lead valve complies with CA AB1953 and VT S.152 Ultra-Low Lead Law. The water damage protection package has a Water Cop valve electric actuator that uses 110VAC, a one inch low lead brass ball valve with platform (WaterCop ready) and three single probe moisture sensors , that detect water and sound a local water alarm . Use the security system alarm interface on the electric ball valve actuator to connect this water damage protection system to a monitored home security system. Protection against water damage in homes, condominiums and businesses means lower insurance premiums from many companies. Slow and fast leaks from toilets, washing machines, dishwashers, etc. damage estimates are often in the tens of thousands. Install this WaterCop with electric water valve and place moisture sensors in as many places as you wish or can afford. Included in this package are three water sensor alarms that operate either on AA batteries or on optional AC adapters (not included). The Water Cop electric water valve responds to radio signals from these water alarms placed under or near water using appliances and shuts off the water to that zone or the entire building. Contents: Water Cop Automatic Actuator with 1 Inch Full Port Brass Ball Valve that is no lead, meeting California and Vermont water valve requirements, a Home Security Interface (on the actuator) and three (3) Single Probe Water Hound Moisture Sensors. The built-in I/O port has an RJ45 connection. |
| Water Cop Installation Locations: |
After existing main water line shut off valve or inside building if shut-off is outside. Maximum working water pressure is 125 PSIG. |
| Installation Time: |
Professional installation: one to two hours+. For new dwellings, install WaterCop Ready Water Valves and add WaterCop later. |
| WaterCop Power Requirements: | 120VAC electrical outlet. outlet. |
| Water Cop Security System Option: | Low voltage interface terminal direct wires to home security alarm system or home automation control panel. For security systems with auxiliary outputs, contact security system dealer/installer for interface installation.
|
WaterHounds: - Local Water Alarm for Moisture
- Transmit Signals for to Activate Your WaterCop.
- For Maximum Water Leak Detection, Place Water Hound Water Alarm Near Every Water Using Appliance.
| - Power Source: 2 AA Batteries (Not Included) or AC Power Adapter (Not Included)
- Operational Modes: WaterCop Activation Device Plus Independent Moisture Sensing Water Alarm
- Alarm Intensity: Similar to Watch Alarm or Pager
- Single Probe: One 9.75 Ft. Cord and One Transmitter/Alarm
- Twin Probe: Two 9.75 Ft. Cords and One Transmitter/Alarm
- Operational Distance from WaterCop: Up to 200 Feet. Frequency goes thru sheetrock and concrete. Significant metal construction may reduce range. Suggestion: test WaterCop range for water leak detection before installation.
|
| Starter Kit Contents: | WaterCop with No Lead Brass Ball Valve to fit a one inch water pipe, Actuator to open and close the valve and Three Water Hounds (Single Probe) to monitor washing machine, hot water heater, refrigerator or dishwasher. |
Additional Sensors Available: | WaterCop supports an unlimited number of WaterHounds for water leak detection. |
| Additional WaterCop Valves: |
"Zoned" protection for large houses or buildings. Note: Each WaterCop and related flood sensors can be programmed for specific zones.
|
NOTE to Contractors: Install WaterCop Ready Water Valves. | Inexpensive. Add WaterCop later with a few screws. |
| Leak Detection Sensor Specifics: | - Sensor probe contacts: gold-plated for reliability.
- Frequency; 400 - 500 MHz. At trade shows, there was no interference with other FM frequencies.
- Change communication codes: Dip switches on sensors and receivers. 4 switches; 48 possible codes means 48 possible zones with additional WaterCop valves.
- Battery Life: Alkaline about 1 year. Titanium, about 2 years.
- Low battery: units "chirp."
|
| Notes: | - Manual override for closed valve. If power fails, unscrew and remove water valve actuator and turn valve stem with wrench 1/4 turn.
|
| Warranty: | One Year Manufacturer's Warranty by Dynaquip |
HTML
PDF
