1120 Series Child Safety Window Guards for Non-Sleeping Areas. Fixed Window Guards are New York City Approved #HDWG 05-87-86. Use White John Sterling 1125 only in Non-Sleeping Areas. Fixed Guards are 25 Inches high and extend from 23 to 42 inches in width. Install only in double hung windows to meet code. WILL NOT OPEN.
Non-Opening Window Guards.1120 Series. 4.5 inch
spacing between the bars. These can be ordered in White or Black. These are
secured with 2.5 inch #10 One Way Screws. To remove the guards, you must break
off the screw head and drill out the screw.
- JS-1123-P 3 Bars 15" H X 23-42"W: Maximum Height Protected: 19"
- JS-1123-S 3 Bars 15" H X 14-24"W: Maximum Height Protected: 19"
- JS-1123-L 3 Bars 15" H X 42-58"W: Maximum Height Protected: 19"
- JS-1124 4 Bars 20"H X 23-42 "W: Maximum Height Protected: 24"
- JS-1125 5 Bars 25"H X 23-42" W: Maximum Height Protected: 29"
NOTE: For sleeping area window guard installations in New York City, check with your local borough for code requirements.
John Sterling window guards have solid steel bars to add security to any window. For baby and child safety, install window guards on any window more than 12 feet above ground level, windows 2nd through 6th story, or at any level where a child could fall or climb through an open window. Window screens are not strong enough to keep children safe from window falls. Check local city codes prior to help you select the proper type of window guards to protect your children.
John Sterling Security Window Guard 1120 Series Features:
Window Type to Protect: Double Hung
Location of Windows: Not in a sleeping Room
Spacing between bars: 4.5 inches.
Diameter of Bars: 5/16 Inch.
Standard Color: Off White. Note: Black option requires 3 to 6 weeks for manufacture.
Construction: Steel window guards
Strength Test: Tested to withstand 150 lb. force at maximum extended width.
Permanently Fixed: Do NOT swing open for easy exit in case of emergency.
Manufacturer: Knape & Vogt, Michigan
Made in USA.
Manufacturers Limited Warranty: Replacement of any part found defective in material or workmanship. Warranty is limited strictly to replacement of the defective part and does not cover any other expenses which may arise in the use or replacement of such part.
Mounting Options: Recessed or Surface Mount. Surface Mount burglar bar installation is easier as screws are easier to drive and less accessible to intruders on the outside.
Tamper Resistant: Option to drill out the Phillips cross slots in each screw to make tamper resistant.
Installation Options: Double Hung windows only. Mount security bars over both upper and lower window sashes or over lower sash only as desired.
WARNING for Series 1120 Series Sterling Window Guards:
Use of this product on a fire escape window in New York is illegal, could be a serious safety hazard and could result in a fine by the Department of Buildings. Some communities require a quick means of easy escape from window guards in some applications. Check your local codes.
Sterling Window Security Guards when properly installed will tend to discourage illegal intruders. But no protection is absolute. With enough time and tools a determined criminal can defeat any barrier.
Installation Requirements:
Install only in solid, non-rotting window tracks. Expand Guard to fit tightly into outside window track.
Temporarily support Guard in level position NO MORE THAN 4-1/2 inches from sill to upper half of bottom bar . Mark location of holes on each side. Remove Guard and drill 5/32" diameter. pilot holes 1" deep.
Re-position Guard and mount with #10 one way screws (included.)
Raise the inner window NO MORE THAN 4-1/2" above the lower half of the top bar. Position "L" shaped
stops so as to limit the opening above the Window Guard to a maximum of 4-1/2.
