John Sterling 1134 is 14 Inches High by 24 to 42 Inches Wide with Locking Hole, for Sleeping and Non-Sleeping Areas. Use this windowguard to protect basement, garage and home windows from home invasions while protecting children from window falls . Install burglar barson double hung windows with a 14 Inch to 18 Inch height opening and a 24 to 42 Inch width opening. Mount vertically to protect sliders or casements that are 24 to 42 inches high with a horizontal opening of 14 to 18 Inches.
Each security bar needs a vertical space of 14 3/16 inches for mounting and provides a security area that is 12 1/2 inches. These hinged security bars are made from 3/8" solid steel bars with heavy-duty welded channels.
Finish is white enamel. Surface or recess mount. Use a padlock or the safety release pin. Mounting hardware
is included. For child safety there is a 3-1/2" spacing between each bar.
These Swing Open John Sterling Security Guards Include a Locking Channel and Locking Hole for Padlock or Safety Release Pin. Install Horizontally or Vertically to Protect Double Hung Windows, Sliders or Casement Windows.
Protect Children in Homes, Day Care Centers and Apartment Buildings. Protect garages, basement windows and other windows from home invasion.
NOTE: Check with your local building inspection department for window guard requirements for your locality.
NOTE: New Jersey Law now requires the window guard cover the entire lower half of a double hung or single hung window, from the top of the sill to the bottom half of the upper sash, with less than a 4 inch gap above and below the guard. Choose BK-1130 series fixed mount window security guards for Non-Sleeping Room Windows.
Childproofing windows with 1120, 1130 or 1170 series off-white John Sterling window guards is a must for multi-level homes, apartments, condos or homes where windows are close to the floor. John Sterling window guards have solid steel bars to add security to any window. For baby and child safety, install window guards on any window more than 12 feet above ground level, windows 2nd through 6th story, or at any level where a child could fall or climb through an open window. Window screens are not strong enough to keep children safe from window falls. Check local city codes prior to help you select the proper type of window guards to protect your children.
John Sterling Security and Child Safety Window Guard 1130 Series. Swing Open Escape Type Window Guard Features:
Window Type to Protect: Double hung, sliders or casement windows.
Window Locations: Sleeping and non-sleeping rooms.
Bar Spacing: 3.5 inches. Exceeds 4 inch recommended safety standard for child window bars.
Bar Diameter: 5/16 Inch.
Mounting Options: Horizontal or vertical installations.
Stackable: Fit units side by side or vertical stack to fit window width or height.
Standard Color: Off White. Brown option by custom order.
Construction: Steel window guards
Strength Test: Tested to withstand 150 lb. force at maximum extended width.
Operational Type: Swing Open emergency exit window guards. Are NOT removable from window.
Locking Hole: Locking clip or lock option.
Manufacturer: John Sterling Corporation, Richmond IL.
Made in USA.
Manufacturers Limited Warranty: Replacement of any part found defective in material or workmanship. Warranty is limited strictly to replacement of the defective part and does not cover any other expenses which may arise in the use or replacement of such part.
Mounting Options: Recessed or Surface Mount. Surface Mount burglar bar installation is easier as screws are easier to drive and less accessible to intruders on the outside.
Tamper Resistant: Option to drill out the Phillips cross slots in each screw to make tamper resistant.
Installation Options: Double Hung, Sliders or Casement Windows only. Mount security bars over both upper and lower window sashes or over lower sash only as desired.
Sterling Child and Window Security Guards when properly installed will tend to discourage illegal intruders. But no protection is absolute. With enough time and tools a determined criminal can defeat any barrier.
Installation Requirements:
Install only in solid, non-rotting window tracks. Expand Guard to fit tightly into outside window track.
Temporarily support Guard in level position NO MORE THAN 4 inches from sill to upper half of bottom bar . Mark location of holes on each side. Remove Guard and drill 5/32" diameter. pilot holes 1 inch deep.
Re-position Guard and mount with #10 one way screws (included.)
Raise the inner window NO MORE THAN 4 inches above the lower half of the top bar. Position "L" shaped stops so as to limit the opening above the Window Guard to a maximum of 4 inches.
